Вот результат sudo smartctl -a /dev/sdb | less:
Код:
smartctl 6.2 2013-04-20 r3812 [i686-linux-3.11.0-18-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital My Passport (USB, AF)
Device Model: WDC WD10TMVW-11ZSMS5
Serial Number: WD-WXG1A91X8304
LU WWN Device Id: 5 0014ee 10498ac79
Firmware Version: 01.01A01
User Capacity: 1*000*204*886*016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Mar 21 10:55:13 2014 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (24900) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 242) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 3
3 Spin_Up_Time 0x0027 173 141 021 Pre-fail Always - 4341
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2096
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 001 001 000 Old_age Always - 65535
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2873
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1241
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 612
193 Load_Cycle_Count 0x0032 192 192 000 Old_age Always - 25137
194 Temperature_Celsius 0x0022 118 100 000 Old_age Always - 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 196 196 000 Old_age Always - 760
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 6 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 occurred at disk power-on lifetime: 2873 hours (119 days + 17 hours)
When the command that caused the error occurred, the device was in standby mode.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 01:03:51.574 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:03:51.568 IDENTIFY DEVICE
e0 00 0a 00 00 00 00 00 01:02:33.407 STANDBY IMMEDIATE
b0 d0 00 00 4f c2 00 00 00:58:38.607 SMART READ DATA
Error 5 occurred at disk power-on lifetime: 2867 hours (119 days + 11 hours)
When the command that caused the error occurred, the device was in standby mode.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 00:55:29.640 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 00:55:29.634 IDENTIFY DEVICE
e0 00 0a 00 00 00 00 00 00:32:14.517 STANDBY IMMEDIATE
b0 d0 00 00 4f c2 00 00 00:29:31.091 SMART READ DATA
Error 4 occurred at disk power-on lifetime: 2865 hours (119 days + 9 hours)
When the command that caused the error occurred, the device was in standby mode.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 00:34:07.854 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 00:34:07.848 IDENTIFY DEVICE
e0 00 0a 00 00 00 00 00 00:32:13.504 STANDBY IMMEDIATE
b0 d0 00 00 4f c2 00 00 00:29:31.118 SMART READ DATA
Error 3 occurred at disk power-on lifetime: 2863 hours (119 days + 7 hours)
When the command that caused the error occurred, the device was in standby mode.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 07:09:41.343 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 07:09:41.337 IDENTIFY DEVICE
e0 00 0a 00 00 00 00 00 04:17:50.355 STANDBY IMMEDIATE
b0 d0 00 00 4f c2 00 00 04:13:55.645 SMART READ DATA
Error 2 occurred at disk power-on lifetime: 2859 hours (119 days + 3 hours)
When the command that caused the error occurred, the device was in standby mode.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 03:19:54.507 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 03:19:54.501 IDENTIFY DEVICE
e0 00 0a 00 00 00 00 00 01:40:49.134 STANDBY IMMEDIATE
b0 d0 00 00 4f c2 00 00 01:40:15.027 SMART READ DATA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Сильно настораживает вот это:
Цитата:
rror 5 occurred at disk power-on lifetime: 2867 hours (119 days + 11 hours)
When the command that caused the error occurred, the device was in standby mode.
|
их пять штук. Выходит, проблемы с питанием, т. е. его потерей?
Сейчас запустил тест (smartctl --test=long /dev/sdb), там посмотрю...
Цитата DVDshnik:
|
Угадал... К двум подключить пробуйте, уж очень вероятно, что проблема из-за нехватки питания может быть. »
|
Не, там без вариантов... В диск втыкается плоский широкий разъем. На компьютер - USB3... Сейчас вот мысль появилась: а если ЮСБ-порт недодает питание
. Откуда тогда щелчки при записи...
Тест закончится - подключу к ЮСБ-выходу с мамы (на задней стенке). Хотя тут - глупо что-то ожидать. Подключал же к другим компам...
