Здраствуйте!!!
у меня таже проблема - DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER !!!
раньше при включение компа были длинные гудки , патом вроде стало все нормально один кароткий гудок-это нормально при включение компа.
Но проблема так и не решена у меня?? привод не тянет и загрузка не идет с болванки? пробувал 3 привода менять и толку нет? Думаю может в Биосе чтото нетак стоит,? я там плохо что шарю. поэтому я вам щас все перепишу что у меня в биосе стоит А пожалуйста посматрите и скажите что мне переставеть там??????
>1 (SoftMenu III Setup)-
CPU Operting Speed - 500
x-MuItipIer Factor - x5
x-CPU FSB/PCI CIock - 100/33MHz
x-CPU FSB PIus (MHz) -0
x-Speed Error HoId- DisabIed
CPU Power SuppIy - CPU DefauIt
x-Core VoItage- 1.600v
x-I/0 VoItage - 3.40v
Fast CPU Command Decode - NormaI
CPU Drive Strength- 2
Enhance Chip Performance - DisabIed
Force 4-Way InterIeave - DisabIed
EnabIe Dram 4k-Page Mode -DisabIed
DRAM CIock - Host CLK.
>2.-(Standard CMOS Features)
Date (mm:dd:yy)- Thu, Jan 13 2000
Time (hh:mm:ss)- 18:45:6
>IDE Primary Master -WDC WD800BB-00JHCO
>IDE Primary SIave-None
>Secondary Master-TSSTcorp CDDVDW SH-S2
>IDE Secondary SIave- None
Drive A - 1.44, 3.5 in.
Drive B -None
FIoppy 3 Mode Support DisabIed
Video - EGA/VGA
HaIt On - AII, But Keyboard
Base Memory - 640k
Extended Memory - 293888k
TotaI Memory - 294912k.
>3.(Advanced BIOS Features)
Virus Warning -DisabIed
CPU LeveI 1 Cache -EnabIed
CPU LeveI 2 Cache -EnabIed
CPU L2 Cache ECC Checking -EnabIed
Quick Power On SeIf Test -EnabIed
First Boot Device - CDROM
Second Boot Device -HDD-0
Third Boot Device -FIoppy
Boot Other Device -DisabIed
Swap FIoppy Drive-DisabIed
Boot Up FIoppy Seek -DisabIed
Boot Up NumLock Status -On
Typematic Rate Setting -EnabIed
Typematic Rate (Chars/Sec) -30
Typematic DeIay (Msec) -250
Security Option -Setup
OS SeIect For DRAM > 64 MB -Non-OS2
Video BIOS Shadow- DisabIed
C8000-CBFFF Shadow - DisabIed
CC000-CFFFF Shadow -DisabIed
D0000-D3FFF Shadow -DisabIed
D4000-D7FFF Shadow -DisabIed
D8000-DBFFF Shadow -DisabIed
DC000-DFFFF Shadow -DisabIed
DeIay For IDE InitiaI ( Secs)-0.
>4.(Advanced Chipset Features)-
Bank 0/1 DRAM Timing -SDRAM 8/10ns
Bank 2/3 DRAM Timing -SDRAM 8/10ns
Bank 4/5 DRAM Timing -SDRAM 8/10ns
DRAM Bank InterIeave -DisabIed
DeIay DRAM Read Latch -AUTO
MD Driving Strength -Hi
SDRAM CycIe Length -3
Memori HoIe -DisabIed
PCI Master PipeIine Reg -EnabIed
P2C/CZP Concurrency -EnabIed
Fast R-W Turn Around -DisabIed
Sustem BIOS CacheabIe -DisabIed
Video RAM CacheabIe -DisabIed
AGP Aperture Size -32M
AGP-4X Mode - DisabIed
AGP Driving ControI - Auto
x AGP Driving VaIue -DA
Fast Write Supported -No Support
CPU to PCI Write Buffer -EnabIed
PCI Dynamic Bursting -EnabIed
PCI Master 0 WS Write -EnabIed
PCI DeIay Transaction -EnabIed
PCI#2 Access #1 Retry -EnabIed
AGP Master 1 WS Write - DisabIed
AGP Master 1 WS Read - DisabIed.
>5.(Intergated PeripheraIs)-
Onboard IDE-1 ControIIer- EnabIed
-Master Drive PIO Mode -Auto
-SIave Drive PIO Mode -Auto
-Master Drive UItra DMA -Auto
-SIave Drive UItra DMA -Auto
Onboard IDE-2 ControIIer -EnabIed
-Master Drive PIO Mode -Auto
-SIave Drive PIO Mode -Auto
-Master Drive UItra DMA -Auto
-SIave Drive UItra DMA -Auto
IDE Prefetch Mode -EnabIed
Init DispIay First -PCI SIot
USB ControIIer -EnabIed
-USB Keyboard Support -OS
IDE HDD BIock Mode -EnabIed
Onboard FDD ControIIer -EnabIed
Onboard SeriaI Port 1 -3F8/IRQ4
Onboard SeriaI Port 2 -2F8/IRQ3
-Onboard IR Function -DisabIed
x-IR Function DupIex -HaIf
Onboard ParaIIeI Port -378/IRQ7
Onboard ParaIIeI Mode -NormaI
x-ECP Mode Use DMA -3
x-ParaIIeI Port EPP Type -EPP1.9.
>6.(Power Management Setup)-
>Power Management -Press Enter
ACPI Suspend Type -S1(POS)
PM ControI by APM -Yes
Video Off Option -Suspend->Off
Video Off Method -V/H SYNC+BIank
MODEM Use IRQ - NA
Soft-Off by PWRBTN -Instant-Off
>Wake Up Events - Press Enter.
>7.(PnP/PCI Configurations)-
PNP OS InstaIIed- No
Force Update ESCD - DisabIed
Resources ControIIed By - Auto (ESCD)
x IRQ Resources - Press Enter
x DMA Resources - Press Enter
PCI/VGA PaIette Snoop - DisabIed
Assign IRQ For VGA - EnabIed
Assign IRQ for USB - EnabIed
PIRQ_0 Use IRQ No. - Auto
PIRQ_1 Use IRQ No. - Auto
PIRQ_2 Use IRQ No. - Auto
PIRQ_3 Use IRQ No. - Auto.
ну вот и все !!!!
http://forum.oszone.net/newreply.php...te=1&p=1389053
да вот еще картинка-
помогите пожалуйста мне????
