[ruslandh]

А Debian не для начинающих что ли? »

Нет, конечно, ни для новичков.

И если честно, то он отстаёт от последних версий пакетов.

[mrcnn]

Мне удалрсь зайти в интернет из федоры посредством
pppoe-setup
sbin/ifup ppp0
в дебианепо всей видимости делается также

[mrcnn]

В дебиане pppoe-setup запусьить не удалось, так как он сказал, что нет файла /etc/ppp/pppoe.conf,.
Установил из портов pppoeconf, который изменил файл /etc/ppp/peers/dsl-provider

# Configuration file for PPP, using PPP over Ethernet # to connect to a DSL provider. # # See the manual page pppd(8) for information on all the options. ## # Section 1 # # Stuff to configure... # MUST CHANGE: Uncomment the following line, replacing the user@provider.net # by the DSL user name given to your by your DSL provider. # (There should be a matching entry in /etc/ppp/pap-secrets with the password.) #user myusername@myprovider.net # Use the pppoe program to send the ppp packets over the Ethernet link # This line should work fine if this computer is the only one accessing # the Internet through this DSL connection. This is the right line to use # for most people. #pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1452" # An even more conservative version of the previous line, if things # don't work using -m 1452... #pty "/usr/sbin/pppoe -I eth0 -T 80 -m 1412" # If the computer connected to the Internet using pppoe is not being used # by other computers as a gateway to the Internet, you can try the following # line instead, for a small gain in speed: #pty "/usr/sbin/pppoe -I eth0 -T 80" # The following two options should work fine for most DSL users. # Assumes that your IP address is allocated dynamically # by your DSL provider... noipdefault # Try to get the name server addresses from the ISP. usepeerdns # Use this connection as the default route. # Comment out if you already have the correct default route installed. defaultroute ## # Section 2 # # Uncomment if your DSL provider charges by minute connected # and you want to use demand-dialing. # # Disconnect after 300 seconds (5 minutes) of idle time. #demand #idle 300 ## # Section 3 # # You shouldn't need to change these options... hide-password lcp-echo-interval 20 lcp-echo-failure 3 # Override any connect script that may have been set in /etc/ppp/options. connect /bin/true noauth persist mtu 1492 # RFC 2516, paragraph 7 mandates that the following options MUST NOT be # requested and MUST be rejected if requested by the peer: # Address-and-Control-Field-Compression (ACFC) noaccomp # Asynchronous-Control-Character-Map (ACCM) default-asyncmap plugin rp-pppoe.so eth0 user "381008028"

В /etc/ppp/создаются файлы chap-secrets с указанием имени и пароля

Код:

# Secrets for authentication using CHAP
# client	server	secret			IP addresses

и pap-secrets

Код:

# Secrets for authentication using PAP
# client	server	secret			IP addresses

запуск pon dsl-provider
пытаюсь подключиться - не работает.

Создаю файл pppoe.conf следующего содержания

Код:

#***********************************************************************
#
# pppoe.conf
#
# Configuration file for rp-pppoe.  Edit as appropriate and install in
# /etc/ppp/pppoe.conf
#
# NOTE: This file is used by the adsl-start, adsl-stop, adsl-connect and
#       adsl-status shell scripts.  It is *not* used in any way by the
#       "pppoe" executable.
#
# Copyright (C) 2000 Roaring Penguin Software Inc.
#
# This file may be distributed under the terms of the GNU General
# Public License.
#
# $Id: pppoe.conf,v 1.7 2001/09/14 19:07:39 dfs Exp $
#***********************************************************************

# When you configure a variable, DO NOT leave spaces around the "=" sign.

# Ethernet card connected to ADSL modem
ETH='eth0'

# ADSL user name.  You may have to supply "@provider.com"  Sympatico
# users in Canada do need to include "@sympatico.ca"
# Sympatico uses PAP authentication.  Make sure /etc/ppp/pap-secrets
# contains the right username/password combination.
# For Magma, use xxyyzz@magma.ca
USER='381008028'

# Bring link up on demand?  Default is to leave link up all the time.
# If you want the link to come up on demand, set DEMAND to a number indicating
# the idle time after which the link is brought down.
DEMAND=no
#DEMAND=300

# DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
# NOCHANGE=do not adjust.
DNSTYPE=SERVER

# Obtain DNS server addresses from the peer (recent versions of pppd only)
USEPEERDNS=yes

DNS1=
DNS2=

# Make the PPPoE connection your default route.  Set to
# DEFAULTROUTE=no if you don't want this.
DEFAULTROUTE=yes

### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT

# How long adsl-start waits for a new PPP interface to appear before
# concluding something went wrong.  If you use 0, then adsl-start
# exits immediately with a successful status and does not wait for the
# link to come up.  Time is in seconds.
#
# WARNING WARNING WARNING:
#
# If you are using rp-pppoe on a physically-inaccessible host, set
# CONNECT_TIMEOUT to 0.  This makes SURE that the machine keeps trying
# to connect forever after adsl-start is called.  Otherwise, it will
# give out after CONNECT_TIMEOUT seconds and will not attempt to
# connect again, making it impossible to reach.
CONNECT_TIMEOUT=30

# How often in seconds adsl-start polls to check if link is up
CONNECT_POLL=2

# Specific desired AC Name
ACNAME=

# Specific desired service name
SERVICENAME=

# Character to echo at each poll.  Use PING="" if you don't want
# anything echoed
PING="."

# File where the adsl-connect script writes its process-ID.
# Three files are actually used:
#   $PIDFILE       contains PID of adsl-connect script
#   $PIDFILE.pppoe contains PID of pppoe process
#   $PIDFILE.pppd  contains PID of pppd process
CF_BASE=`basename $CONFIG`
PIDFILE="/var/run/$CF_BASE-pppoe.pid"

# Do you want to use synchronous PPP?  "yes" or "no".  "yes" is much
# easier on CPU usage, but may not work for you.  It is safer to use
# "no", but you may want to experiment with "yes".  "yes" is generally
# safe on Linux machines with the n_hdlc line discipline; unsafe on others.
SYNCHRONOUS=no

# Do you want to clamp the MSS?  Here's how to decide:
# - If you have only a SINGLE computer connected to the ADSL modem, choose
#   "no".
# - If you have a computer acting as a gateway for a LAN, choose "1412".
#   The setting of 1412 is safe for either setup, but uses slightly more
#   CPU power.
CLAMPMSS=1412
#CLAMPMSS=no

# LCP echo interval and failure count.
LCP_INTERVAL=20
LCP_FAILURE=3

# PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
PPPOE_TIMEOUT=80

# Firewalling: One of NONE, STANDALONE or MASQUERADE
FIREWALL=NONE

# Linux kernel-mode plugin for pppd.  If you want to try the kernel-mode
# plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
LINUX_PLUGIN=

# Any extra arguments to pass to pppoe.  Normally, use a blank string
# like this:
PPPOE_EXTRA=""

# Rumour has it that "Citizen's Communications" with a 3Com
# HomeConnect ADSL Modem DualLink requires these extra options:
# PPPOE_EXTRA="-f 3c12:3c13 -S ISP"

# Any extra arguments to pass to pppd.  Normally, use a blank string
# like this:
PPPD_EXTRA=""

запускаю pppoe-setup

sbin/ifup ppp0 не сработал

при запуске системы поднимается коннект. правда, что точно сработало, не понял

[yurfed]

mrcnn, а чем вас не устраивает GDI вариант RPM resource perl(network::vpn::vpnpptp)
pppoe тоже имеется.
ЗЫ Желательно при установке иметь подключение к ин-ту для получения возможных зависимостей.