Добрый День.
Настраиваю факс-сервер hylafax (6.0) на такой системе Centos 5.3.Все настраивал по manam (русс - en) - все вроде как в рабочем состоянии(все службы висят в ожидании, к модему есть обращение).Задача у меня стояла только принимать факсы, отправкой пока не планировал заниматься.
Пришло время опробовать мои труды.
Схема телефонии моего офиса (в офис - заходят 2 телефонные лини и потом маршрутизируются через офисную АТС на внутренние номера) так же есть два факс-аппарата (которые принимают факс в ручном режиме) вместо одного я поставил мой сервер и попробовал принять факс на него (с переключением звонка с другого телефонного аппарата) и получил облом в виде такого лога:
читать дальше »
Apr 13 17:26:16.81: [ 2621]: SESSION BEGIN 000000001 78312557367
Apr 13 17:26:16.81: [ 2621]: HylaFAX (tm) Version 6.0.4
Apr 13 17:26:16.81: [ 2621]: <-- [13:AT+FCLASS=1A\r]
Apr 13 17:26:22.08: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:22.08: [ 2621]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Apr 13 17:26:22.08: [ 2621]: RECV FAX: begin
Apr 13 17:26:22.08: [ 2621]: <-- data [32]
Apr 13 17:26:22.08: [ 2621]: <-- data [2]
Apr 13 17:26:24.06: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:24.06: [ 2621]: <-- data [23]
Apr 13 17:26:24.06: [ 2621]: <-- data [2]
Apr 13 17:26:25.21: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:25.21: [ 2621]: <-- data [13]
Apr 13 17:26:25.21: [ 2621]: <-- data [2]
Apr 13 17:26:26.11: [ 2621]: --> [2:OK]
Apr 13 17:26:26.11: [ 2621]: <-- [9:AT+FRH=3\r]
Apr 13 17:26:33.11: [ 2621]: --> [0:]
Apr 13 17:26:33.11: [ 2621]: MODEM <Empty line>
Apr 13 17:26:33.11: [ 2621]: <-- data [1]
Apr 13 17:26:33.12: [ 2621]: --> [2:OK]
Apr 13 17:26:33.12: [ 2621]: DELAY 70 ms
Apr 13 17:26:33.19: [ 2621]: <-- [9:AT+FTH=3\r]
Apr 13 17:26:33.29: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:33.29: [ 2621]: <-- data [32]
Apr 13 17:26:33.29: [ 2621]: <-- data [2]
Apr 13 17:26:35.27: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:35.27: [ 2621]: <-- data [23]
Apr 13 17:26:35.27: [ 2621]: <-- data [2]
Apr 13 17:26:36.43: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:36.43: [ 2621]: <-- data [13]
Apr 13 17:26:36.43: [ 2621]: <-- data [2]
Apr 13 17:26:37.32: [ 2621]: --> [2:OK]
Apr 13 17:26:37.32: [ 2621]: <-- [9:AT+FRH=3\r]
Apr 13 17:26:44.32: [ 2621]: --> [0:]
Apr 13 17:26:44.32: [ 2621]: MODEM <Empty line>
Apr 13 17:26:44.32: [ 2621]: <-- data [1]
Apr 13 17:26:44.33: [ 2621]: --> [2:OK]
Apr 13 17:26:44.33: [ 2621]: DELAY 70 ms
Apr 13 17:26:44.40: [ 2621]: <-- [9:AT+FTH=3\r]
Apr 13 17:26:44.51: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:44.51: [ 2621]: <-- data [32]
Apr 13 17:26:44.51: [ 2621]: <-- data [2]
Apr 13 17:26:46.49: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:46.49: [ 2621]: <-- data [23]
Apr 13 17:26:46.49: [ 2621]: <-- data [2]
Apr 13 17:26:47.64: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:47.64: [ 2621]: <-- data [13]
Apr 13 17:26:47.64: [ 2621]: <-- data [2]
Apr 13 17:26:48.54: [ 2621]: --> [2:OK]
Apr 13 17:26:48.54: [ 2621]: <-- [9:AT+FRH=3\r]
Apr 13 17:26:55.54: [ 2621]: --> [0:]
Apr 13 17:26:55.54: [ 2621]: MODEM <Empty line>
Apr 13 17:26:55.54: [ 2621]: <-- data [1]
Apr 13 17:26:55.55: [ 2621]: --> [2:OK]
Apr 13 17:26:55.55: [ 2621]: DELAY 70 ms
Apr 13 17:26:55.62: [ 2621]: <-- [9:AT+FTH=3\r]
Apr 13 17:26:55.73: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:55.73: [ 2621]: <-- data [32]
Apr 13 17:26:55.73: [ 2621]: <-- data [2]
Apr 13 17:26:57.71: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:57.71: [ 2621]: <-- data [23]
Apr 13 17:26:57.71: [ 2621]: <-- data [2]
Apr 13 17:26:58.86: [ 2621]: --> [7:CONNECT]
Apr 13 17:26:58.86: [ 2621]: <-- data [13]
Apr 13 17:26:58.86: [ 2621]: <-- data [2]
Apr 13 17:26:59.76: [ 2621]: --> [2:OK]
Apr 13 17:26:59.76: [ 2621]: <-- [9:AT+FRH=3\r]
Apr 13 17:27:06.76: [ 2621]: --> [0:]
Apr 13 17:27:06.76: [ 2621]: MODEM <Empty line>
Apr 13 17:27:06.76: [ 2621]: <-- data [1]
Apr 13 17:27:06.77: [ 2621]: --> [2:OK]
Apr 13 17:27:06.77: [ 2621]: RECV FAX: No sender protocol (T.30 T1 timeout)
Apr 13 17:27:06.77: [ 2621]: RECV FAX: end
Apr 13 17:27:06.77: [ 2621]: No sender protocol (T.30 T1 timeout)
Apr 13 17:27:06.77: [ 2621]: SESSION END
Возможно я логики подключения не понял?возможно hylafax'у вообще нужна отдельная линия по мимо АТС?возможно еще настройки нужны когда работаешь с АТС?!
В конфиге в строке FaxNumber прописывал внутренний номер и внешний не получилось!!!
мой конфиг:
читать дальше »
CountryCode: 7
AreaCode: 831
FAXNumber: ???
LongDistancePrefix: 8
InternationalPrefix: 7
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier:
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
MaxCosecutiveBadLines: 30
PercentGoodLines: 50
ModemType: Class1 # use class 1 interface
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: xonxoff # software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
ModemResultCodesCmd: ATQ0X4 # enable result codes
#
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7 # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control
Class1SFLOCmd: "" # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0
ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1
#
# When using AT+FRS=n we see USR modems reset themselves in the middle of sessions
# this is not good. So, we seem to work-around that problem by not using the
# command. Unfortunately, this isn't an ideal thing.
#
Class1SwitchingCmd: "<delay\0727>"
Спасибо!
