[glestwid]

Вот мой OVPN файл

############################################################################### # OpenVPN 2.0 Sample Configuration File # for PacketiX VPN / SoftEther VPN Server # # !!! AUTO-GENERATED BY SOFTETHER VPN SERVER MANAGEMENT TOOL !!! # # !!! YOU HAVE TO REVIEW IT BEFORE USE AND MODIFY IT AS NECESSARY !!! # # This configuration file is auto-generated. You might use this config file # in order to connect to the PacketiX VPN / SoftEther VPN Server. # However, before you try it, you should review the descriptions of the file # to determine the necessity to modify to suitable for your real environment. # If necessary, you have to modify a little adequately on the file. # For example, the IP address or the hostname as a destination VPN Server # should be confirmed. # # Note that to use OpenVPN 2.0, you have to put the certification file of # the destination VPN Server on the OpenVPN Client computer when you use this # config file. Please refer the below descriptions carefully. ############################################################################### # Specify the type of the layer of the VPN connection. # # To connect to the VPN Server as a "Remote-Access VPN Client PC", # specify 'dev tun'. (Layer-3 IP Routing Mode) # # To connect to the VPN Server as a bridging equipment of "Site-to-Site VPN", # specify 'dev tap'. (Layer-2 Ethernet Bridgine Mode) dev tun ############################################################################### # Specify the underlying protocol beyond the Internet. # Note that this setting must be correspond with the listening setting on # the VPN Server. # # Specify either 'proto tcp' or 'proto udp'. proto tcp ############################################################################### # The destination hostname / IP address, and port number of # the target VPN Server. # # You have to specify as 'remote <HOSTNAME> <PORT>'. You can also # specify the IP address instead of the hostname. # # Note that the auto-generated below hostname are a "auto-detected # IP address" of the VPN Server. You have to confirm the correctness # beforehand. # # When you want to connect to the VPN Server by using TCP protocol, # the port number of the destination TCP port should be same as one of # the available TCP listeners on the VPN Server. # # When you use UDP protocol, the port number must same as the configuration # setting of "OpenVPN Server Compatible Function" on the VPN Server. remote vpn566803988.opengw.net 1720 #push "route 192.168.0.0 255.255.254.0 vpn_gateway 100" #route-metric 100 push "redirect-gateway route metric 3" ############################################################################### # The HTTP/HTTPS proxy setting. # # Only if you have to use the Internet via a proxy, uncomment the below # two lines and specify the proxy address and the port number. # In the case of using proxy-authentication, refer the OpenVPN manual. ;http-proxy-retry ;http-proxy [proxy server] [proxy port] ############################################################################### # The encryption and authentication algorithm. # # Default setting is good. Modify it as you prefer. # When you specify an unsupported algorithm, the error will occur. # # The supported algorithms are as follows: # cipher: [NULL-CIPHER] NULL AES-128-CBC AES-192-CBC AES-256-CBC BF-CBC # CAST-CBC CAST5-CBC DES-CBC DES-EDE-CBC DES-EDE3-CBC DESX-CBC # RC2-40-CBC RC2-64-CBC RC2-CBC # auth: SHA SHA1 MD5 MD4 RMD160 cipher AES-128-CBC auth SHA1 ############################################################################### # Other parameters necessary to connect to the VPN Server. # # It is not recommended to modify it unless you have a particular need. resolv-retry infinite nobind persist-key persist-tun client verb 3 #auth-user-pass ############################################################################### # The certificate file of the destination VPN Server. # # The CA certificate file is embedded in the inline format. # You can replace this CA contents if necessary. # Please note that if the server certificate is not a self-signed, you have to # specify the signer's root certificate (CA) here. <ca> -----BEGIN CERTIFICATE----- -----END CERTIFICATE----- </ca> ############################################################################### # The client certificate file (dummy). # # In some implementations of OpenVPN Client software # (for example: OpenVPN Client for iOS), # a pair of client certificate and private key must be included on the # configuration file due to the limitation of the client. # So this sample configuration file has a dummy pair of client certificate # and private key as follows.

Серверу я не хозяин, так что не в курсе что и как там