Помогите пожалуйста с конфигурацией ядра под Mandrake 9.1

Помогите пожалуйста с конфигурацией ядра
пытаюсь собрать его уже 2 недели и постоянно возникают какието ошибки
Вышлите пожалуйста файл конфигурации
-----
Моя конфигурация PIII/256mb/HDD-10Gb/ESS Solo1/Net IntelPro100/Win Modem LT/Ati Mobility 8mb/-
COMPAQ ARMADA E500

[s]Исправлено: eu, 11:08 27-06-2003[/s]

Добавлено:

Linux version 2.4.21-0.13mdk (flepied@bi.mandrakesoft.com) (gcc version 3.2.2 (Mandrake Linux 9.1 3.2.2-3mdk))
#1 Fri Mar 14 15:08:06 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3800 (reserved)
BIOS-e820: 000000000fff3800 - 0000000010000000 (ACPI NVS)
255MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=306 devfs=mount acpi=off
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 696.414 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1389.36 BogoMIPS
Memory: 255764k/262080k available (1410k kernel code, 5928k reserved, 1118k data, 136k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030122
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xf0478, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Discovered primary peer bus 04 [IRQ]
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
vesafb: framebuffer at 0x40000000, mapped to 0xd0800000, size 8128k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:509c
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... no good signature found.
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
PCI: Found IRQ 11 for device 00:09.1
PCI: Sharing IRQ 11 with 00:08.0
PCI: Sharing IRQ 11 with 00:09.0
Redundant entry in serial pci_table.  Please send the output of
lspci -vv, this message (11c1,0445,8086,2204)
and the manufacturer and name of serial board or modem board
to serial-pci-info@lists.sourceforge.net.
register_serial(): autoconfig failed
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
   ide0: BM-DMA at 0x3420-0x3427, BIOS settings: hda:DMA, hdb:DMA
hda: HITACHI_DK23AA-12, ATA DISK drive
hdb: Compaq DVD-ROM DRN-8080B, ATAPI CD/DVD-ROM drive
blk: queue c03cb420, I/O limit 4095Mb (mask 0xffffffff)
ide2: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: host protected area => 1
hda: 23579136 sectors (12073 MB) w/512KiB Cache, CHS=1559/240/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 108k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:32:56 Mar 14 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x3400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Adding Swap: 506480k swap-space (priority -1)
hub.c: new USB device 00:07.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00e) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb1:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
MSDOS FS: IO charset koi8-r
MSDOS FS: Using codepage 866
MSDOS FS: IO charset koi8-r
MSDOS FS: Using codepage 866
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
PCI: Found IRQ 11 for device 00:09.0
PCI: Sharing IRQ 11 with 00:08.0
PCI: Sharing IRQ 11 with 00:09.1
eth0: OEM i82557/i82558 10/100 Ethernet, 00:D0:59:1A:E6:54, IRQ 11.
 Board assembly 98004c-000, Physical connectors present: RJ45
 Primary interface chip i82555 PHY #1.
 General self-test: passed.
 Serial sub-system self-test: passed.
 Internal registers self-test: passed.
 ROM checksum self-test: passed (0xdbd8681d).
inserting floppy driver for 2.4.21-0.13mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PCI: Found IRQ 11 for device 00:08.0
PCI: Sharing IRQ 11 with 00:09.0
PCI: Sharing IRQ 11 with 00:09.1
maestro: Configuring ESS Maestro 2E found at IO 0x3000 IRQ 11
maestro:  subvendor id: 0xb1120e11
maestro: not attempting power management.
maestro: AC97 Codec detected: v: 0x83847609 caps: 0x6940 pwr: 0xf
maestro: 1 channels configured.
maestro: version 0.15 time 15:30:11 Mar 14 2003
hdb: ATAPI 24X DVD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
mtrr: 0x40000000,0x800000 overlaps existing 0x40000000,0x400000
mtrr: 0x40000000,0x800000 overlaps existing 0x40000000,0x400000
udf: registering filesystem
cdrom: open failed.
UDF-fs DEBUG lowlevel.c:57:udf_get_last_session: XA disk: no, vol_desc_start=0
UDF-fs DEBUG super.c:1426:udf_read_super: Multi-session=0
UDF-fs DEBUG super.c:415:udf_vrs: Starting at sector 16 (2048 byte sectors)
UDF-fs DEBUG super.c:442:udf_vrs: ISO9660 Primary Volume Descriptor found
UDF-fs DEBUG super.c:439:udf_vrs: ISO9660 Boot Record found
UDF-fs DEBUG super.c:445:udf_vrs: ISO9660 Supplementary Volume Descriptor found
UDF-fs DEBUG super.c:451:udf_vrs: ISO9660 Volume Descriptor Set Terminator found
UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
UDF-fs DEBUG lowlevel.c:57:udf_get_last_session: XA disk: no, vol_desc_start=0
UDF-fs DEBUG super.c:1426:udf_read_super: Multi-session=0
UDF-fs DEBUG super.c:415:udf_vrs: Starting at sector 16 (2048 byte sectors)
UDF-fs DEBUG super.c:442:udf_vrs: ISO9660 Primary Volume Descriptor found
UDF-fs DEBUG super.c:445:udf_vrs: ISO9660 Supplementary Volume Descriptor found
UDF-fs DEBUG super.c:451:udf_vrs: ISO9660 Volume Descriptor Set Terminator found
UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
mtrr: 0x40000000,0x800000 overlaps existing 0x40000000,0x400000
mtrr: 0x40000000,0x800000 overlaps existing 0x40000000,0x400000
mtrr: 0x40000000,0x800000 overlaps existing 0x40000000,0x400000
mtrr: 0x40000000,0x800000 overlaps existing 0x40000000,0x400000

Добавлено:

E-mail: admin@compozitor.spb.ru , titan001@nwgsm.com