| Eakdrazile |
25-02-2010 20:37 1355935 |
Подключение PPPoE в Frugalware 1.1 "Getorin"
Доброго времени суток всем. Суть вопроса такова: настройки локальной сети через netconfig настроил, вывод ifconfig:
Код:
root@eakdrazile:~# ifconfig
eth0 Link encap:Ethernet HWaddr 90:E6:BA:3F:9B:A7
inet addr:192.168.0.216 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::92e6:baff:fe3f:9ba7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3860 errors:0 dropped:0 overruns:0 frame:0
TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:364201 (355.6 Kb) TX bytes:4721 (4.6 Kb)
Interrupt:28 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:388 errors:0 dropped:0 overruns:0 frame:0
TX packets:388 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:30504 (29.7 Kb) TX bytes:30504 (29.7 Kb)
стало быть, все в порядке. Дальше устанавливаю пакеты ppp и rp-pppoe и пытаюсь настроить через pppoe-setup (в Slackware и MOPSlinux таким образом все настраивается и работает на ура):
Код:
root@eakdrazile:~# pppoe-setup
Welcome to the Roaring Penguin PPPoE client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Oh, dear, I don't see the file '/etc/ppp/pppoe.conf' anywhere. Please
re-install the PPPoE client.
этот файл я создал, но оставил пустым и пробовал дальше:
Код:
root@eakdrazile:~# pppoe-setup
Welcome to the Roaring Penguin PPPoE client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Looks good! Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default root): ХХХХХХХ
INTERFACE
>>> Enter the Ethernet interface connected to the DSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default ): eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here: server
PASSWORD
>>> Please enter your PPPoE password: ХХХХХХ
>>> Please re-enter your PPPoE password: ХХХХХХ
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2): 1
** Summary of what you entered **
Ethernet Interface: eth0
User name: ХХХХХХХ
Activate-on-demand: No
DNS addresses: Supplied by ISP's server
Firewalling: STANDALONE
>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
(But first backing it up to /etc/ppp/pap-secrets-bak)
(But first backing it up to /etc/ppp/chap-secrets-bak)
Congratulations, it should be all set up!
Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring
it down. Type 'pppoe-status' to see the link status.
при вводе pppoe-start ничего не происходит, при вводе pppoe-status выдает такое:
Код:
root@eakdrazile:~# pppoe-status
Note: You have enabled demand-connection; pppoe-status may be inaccurate.
pppoe-status: Link is down (can't read pppoe PID file .pppoe)
какие у кого будут соображения? Заранее всем спасибо. |
